Коды ошибок

  1. 2304 UGC user variable
  2. 2305 UGC system variable
  3. 2306 UGC illegal command
  4. 2307 UGC program factor over
  5. 2308 UGC coordinate data
  6. 2309 UGC END syntax
  7. 2310 UGC command over
  8. 2311 UGC command format
  9. 2312 UGC additional parameter
  10. 2313 UGC expression
  11. 2314 UGC figure entry area over
  12. 2315 UGC delete unable
  13. 2316 READ/WRITE no spec.
  14. 2317 READ/WRITE buffer over
  15. 2318 READ/WRITE device NO.
  16. 2319 READ/WRITE data
  17. 2320 READ communication error
  18. 2321 WRITE communication error
  19. 2322 GET/PUT no spec.
  20. 2323 GET/PUT buffer over
  21. 2324 GET/PUT number of figure
  22. 2325 GET/PUT variable designation
  23. 2326 GET numeric data
  24. 2327 Calculation function no spec.
  25. 2328 Sub-program no spec.
  26. 2330 Input/output variable no spec.
  27. 2331 Multiple machining no spec.
  28. 2332 Sub-spindle no spec.
  29. 2334 In-process gauging no spec.
  30. 2335 Post-process gauging no spec.
  31. 2336 Animation no spec.
  32. 2337 Graphic backup data file write
  33. 2338 Spindle orientation no spec.
  34. 2339 Load monitor no spec.
  35. 2340 Thread phase matching no spec.
  36. 2341 Circular thread cutting no spec.
  37. 2342 Circular thread cutting command
  38. 2343 Tool retract no spec.
  39. 2344 Tool retract interrupt enable com.
  40. 2345 Tool retract interrupt disable com.
  41. 2346 Tool retract interrupt return com.
  42. 2347 ROBOT no spec.
  43. 2348 ROBOT program name
  44. 2349 LOADER no spec.
  45. 2350 LOADER program name
  46. 2351 Coupling device program select no spec.
  47. 2353 CHAMFERING G01 mode
  48. 2354 CHAMFERING L over
  49. 2355 CHAMFERING L illegal order
  50. 2356 CHAMFERING X,Z illegal order
  51. 2357 CHAMFERING any angle calculation
  52. 2358 CHAMFERING any angle
  53. 2359 NOSE-R COMP. no spec.
  54. 2360 NOSE-R COMP. NOSE-R > circle-R
  55. 2361 NOSE-R COMP. calculation
  56. 2362 NOSE-R COMP. cancel G00 G01
  57. 2363 NOSE-R COMP. no cross point
  58. 2364 NOSE-R COMP. start up impossible
  59. 2365 NOSE-R COMP. thread cutting cycle
  60. 2366 TOOL RADIUS COMP. no spec.
  61. 2367 TOOL RADIUS COMP. NOSE-R comp. change surface
  62. 2368 TOOL RADIUS COMP. C-axis separation
  63. 2369 TOOL RADIUS COMP. QA command
  64. 2370 TOW-ALONG TAILSTOCK MOVEMENT no spec.
  65. 2371 TOW-ALONG TAILSTOCK MOVEMENT condition

1 2 3 4 5 Вперед >>

 
 

Программирование станков с ЧПУ Okuma OSP-U100L, OSP-U10L. Правила, функции, коды, команды, примеры программ.
При копировании материалов ссылка на сайт обязательна.