Коды ошибок

  1. 2372 LASER MEASUREMENT no spec.
  2. 2373 LASER MEASUREMENT condition
  3. 2374 LAP no spec.
  4. 2375 LAP B illegal order
  5. 2376 LAP D illegal order
  6. 2378 LAP H illegal order
  7. 2379 LAP H-U(W) less than D (M73)
  8. 2380 LAP U(W) illegal order
  9. 2381 LAP U (W) greater than H
  10. 2382 LAP XA(ZA),XB(ZB) illegal order
  11. 2383 LAP calculation
  12. 2384 LAP number of down stair over
  13. 2385 LAP entry in LAP
  14. 2386 LAP sequence name
  15. 2387 LAP control
  16. 2388 LAP G-code
  17. 2389 LAP NOSE-R comp. cancel
  18. 2390 LAP entry in NOSE-R comp.
  19. 2391 LAP shape definition
  20. 2392 MULTI CYCLE B illegal order
  21. 2393 MULTI CYCLE D illegal order
  22. 2394 MULTI CYCLE F illegal order
  23. 2395 MULTI CYCLE H illegal order
  24. 2396 MULTI CYCLE H-U(W) less than D (M73)
  25. 2397 MULTI CYCLE I,K over
  26. 2398 MULTI CYCLE I,K illegal order
  27. 2399 MULTI CYCLE L illegal over
  28. 2400 MULTI CYCLE entry in LAP
  29. 2401 MULTI CYCLE U(W) illegal order
  30. 2402 MULTI CYCLE U(W) greater than H
  31. 2403 MULTI CYCLE X,Z illegal order
  32. 2404 MULTI CYCLE angle
  33. 2405 MULTI CYCLE tool offset
  34. 2406 MULTI CYCLE cycle start point
  35. 2407 MULTI CYCLE entry in NOSE-R comp.
  36. 2408 MULTI CYCLE width
  37. 2409 TOOL LIFE CONTROL no spec.
  38. 2410 TOOL LIFE CONTROL spare tool none
  39. 2411 TOOL LIFE CONTROL tool group
  40. 2412 TOOL LIFE CONTROL no T-entry
  41. 2413 TOOL LIFE CONTROL tool offset group
  42. 2414 TOOL LIFE CONTROL no T-offset
  43. 2415 MULTI-MACHINING CYCLE no spec.
  44. 2416 MULTI-MACHINING CYCLE C
  45. 2417 MULTI MACHINING CYCLE I,K
  46. 2418 MULTI-MACHINING CYCLE Q
  47. 2419 MULTI-MACHINING CYCLE F
  48. 2420 MULTI-MACHINING CYCLE L
  49. 2421 MULTI-MACHINING CYCLE D
  50. 2422 MULTI-MACHINING CYCLE X,Z
  51. 2423 MULTI-MACHINING CYCLE SA
  52. 2424 MULTI-MACHINING CYCLE SA
  53. 2425 MULTI-MACHINING CYCLE A
  54. 2426 MULTI-MACHINING CYCLE thread cycle
  55. 2427 MULTI-MACHINING CYCLE U,W
  56. 2428 MULTI MACHINING CYCLE SB
  57. 2429 MULTI-MACHINING CYCLE Y-axis mode
  58. 2430 ATC no spec.
  59. 2431 ATC syntax
  60. 2432 ATC TC
  61. 2434 ATC TL
  62. 2435 ATC MT
  63. 2436 ATC MG
  64. 2438 M06/M228 command disable
  65. 2444 Carrier axis variable limit over

 

<< Назад 1 2 3 4 5 Вперед >>
 

Программирование станков с ЧПУ Okuma OSP-U100L, OSP-U10L. Правила, функции, коды, команды, примеры программ.
При копировании материалов ссылка на сайт обязательна.